GE GUV27ESSMWW Installationshandbuch PDF herunterladen (Seite 11)

Installation Instructions

CONNECTING DRYER USING

3-WIRE CONNECTION

3-wire Connection

NOT for use in Canada.

DO NOT use for Mobile Home Installations.

NOT for use on new construction.

NOT for use on recreational vehicles.

NOT for use in areas where local codes prohibit

grounding through the neutral conduction.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical

Code requires that new constructions use a 4-wire

connection to an electric dryer. A 4-wire cord must also

be used where local codes do not permit grounding

through the neutral.

3-wire connection is NOT for use on new construction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located on the back.

4. Remove and discard ground strap. Keep the green

ground screw for Step 7.

5. Install 3/4 in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green

ground screw (hole below strain relief bracket).

Tighten all terminal block screws (3) securely.

8. Properly secure power cord to strain relief.

9. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located on the back.

4. Install 3/4-in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to neutral

(center) terminal of block and to green ground

screw on cabinet rear. Tighten all terminal block

screws (3) securely.

7. Properly secure power cord to strain relief.

8. Reinstall the cover.

27” MODELS - CONNECTING AN ELECTRIC DRYER

GREEN GROUND SCREW

AND GROUND STRAP

3 # 10 AWG MINIMUM

COPPER CONDUCTORS

OR 120/240V 30A POWER

SUPPLY CORD KIT

MARKED FOR USE WITH

DRYERS & PROVIDED

WITH CLOSED LOOP OR

SPADE TERMINALS WITH

UPTURNED ENDS (NOT

SUPPLIED).

3/4” UL RECOGNIZED

STRAIN RELIEF

COVER

SCREWS

(3)

STRAIN

RELIEF

BRACKET

HOT

WIRE

HOT

WIRE

NEUTRAL

(White)

REMOVE GROUND STRAP AND DISCARD.

KEEP GREEN GROUND SCREW.

4 # 10 AWG MINIMUM

COPPER CONDUCTORS

OR 120/240V 30A POWER

SUPPLY CORD KIT

MARKED FOR USE WITH

DRYERS & PROVIDED

WITH CLOSED LOOP OR

SPADE TERMINALS WITH

UPTURNED ENDS (NOT

SUPPLIED).

RELOCATE

GREEN GROUND

SCREW HERE

3/4” UL RECOGNIZED

STRAIN RELIEF

COVER

SCREWS

(3)

STRAIN

RELIEF

BRACKET

GREEN OR

YELLOW WIRE

HOT WIRE

HOT

WIRE

NEUTRAL

(White)

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

GE GUV27ESSMWW Installationshandbuch Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein GE GUV27ESSMWW