GE Fanuc AutomationState Logic ProductsState Logic ProcessorFor Series 90 -30 PLCUser’s GuideGFK-0726B March 1998
11-2 State Logic Processor for Series 90–30 PLC User’s Guide – March 1998GFK-0726B-Physical DescriptionThe SLP occupies a single slot in the Series 90
11-3GFK-0726B Chapter 1 State Logic Processor Descriptiona45127OKBDOKRESTARTBATTERYOPENREPLACEMENTBATTERYCONNECTORPORTS1 AND 2SLP 300CURRENTLYINSTALL
11-4 State Logic Processor for Series 90–30 PLC User’s Guide – March 1998GFK-0726B-Operational DescriptionThe State Logic Processor (SLP) uses areas i
2section level 1 1figure bi level 1 table_big level 1 2-1GFK-0726BChapter 2 Installation and MaintenanceThis chapter describes how to install the
22-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BConfigurationUse the Logicmaster 90-30 configuration software to ad
22-3GFK-0726B Chapter 2 Installation and MaintenanceBatteryThe State Logic Processor comes with a 3 volt lithium battery (IC697ACC701) to maintainmem
3section level 1 1figure bi level 1 table_big level 1 3-1GFK-0726BChapter 3 TroubleshootingThis chapter provides procedures for diagnosing State
33-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BCommunications Problems with ECLiPS or OnTOP1. Check that the serial
4section level 1 1figure bi level 1 table_big level 1 4-1GFK-0726BChapter 4 Serial CommunicationsSerial communications with the State Logic Proce
44-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BProgramming Serial CommunicationsThe program communicates through tw
GFL–002Warnings, Cautions, and Notesas Used in this PublicationWarningWarning notices are used in this publication to emphasize that hazardous voltage
44-3GFK-0726B Chapter 4 Serial CommunicationsSerial Port SetupThere are several serial port configuration options. Some of these options are set usi
44-4 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BTable 4-1. Serial Port ParametersParameter SettingsBaud Rate 19.2K
44-5GFK-0726B Chapter 4 Serial CommunicationsSerial CableThe State Logic Processor (SLP) is designed to work with two GE Fanuc standard serialcables.
44-6 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BOther Cable OptionsOther cables that work with the SLP are the IBM-A
44-7GFK-0726B Chapter 4 Serial CommunicationsCustom Made CablesIf you want to make your own cable to connect to some serial device, use the drawing o
44-8 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726Ba4509121345678910111213151617181920212223242514RS–232 DTRSHIELDRS–23
5section level 1 1figure bi level 1 table_big level 1 5-1GFK-0726BChapter 5 SpecificationsTable 5-1. Serial Ports 1 RS-232 1 RS-422/485Memory B
55-2 State Logic Processor for Series 90-30 PLC User’s Guide – March 1998GFK-0726BTable 5-3. Firmware SpecificationsTasks 256States Per Task 255Integ
GE Fanuc Automation North America, Inc. GFJ–317CSoftware License AgreementYOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE OPENING
iii GFK-0726BPrefaceContent of this ManualChapter 1. State Logic Processor DescriptionChapter 2. Installation and MaintenanceChapter 3. Troublesho
Contents viiGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998Chapter 1 State Logic Processor Description 1-1 . . . . . .
Contents viiiGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998
Contents ixGFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998
1restart lowapp ARestart oddapp: ARestarts for autonumbers that do not restart ineach chapter. figure bi level 1, reset table_big level 1, reset cha
Kommentare zu diesen Handbüchern