Ge GNSF35Z Bedienungsanleitung

Water SofteningsystemSafety Information . . . . . . . . . . . . .2Installation Instructions . . .3–12Step-by-step instructions . . . . . . .6–12Oper

Installation Instructions10CONNECT TO ELECTRICAL POWERTo gain access to the transformer/power cordassembly, remove the salt hole cover from thesoftene

Installation Instructions11SET WATER HARDNESS NUMBER (CONT.)3. When the display shows your water hardness (in grains per gallon), press SELECT to acce

Installation Instructions12SPECIFICATIONS/DIMENSIONSThis system conforms to NSF/ANSI 44 for the specific capacity claims as verified and substantiated

About the water softener system. ge.comServiceWhen the water softening system is providingsoft water, it is called “Service.” During service,hard wate

14Breaking a Salt BridgeSometimes, a hard crust or salt bridge forms inthe salt storage area. It is usually caused by highhumidity or the wrong kind o

15ge.comDuring normal operation, the present time of day and AM or PM show in the control displayarea. When the demand computer determines a recharge

About the water softener system.16To remove an error code: 1. Unplug transformer. 2. Correct defect. 3. Plug transformer in.4. Wait for at least 6 mi

17ge.com1. To enter diagnostics, press and hold theSELECT button until (000 – –) shows in the display.A The first 3 digits indicate water meteroperati

About the water softener system.18This check verifies proper operation of the valvemotor, brine tank fill, brine draw, regenerationflow rates and othe

19Care and cleaning of the water softening system. ge.comBrine (salt dissolved in water) is needed for eachand every recharge. The water for making br

IMPORTANT SAFETY INFORMATION.READ ALL INSTRUCTIONS BEFORE USING.SAFETY PRECAUTIONS Check and comply with your state and local codes.You must follow t

20Troubleshooting Tips Save time and money! Review the chart on the followingpages first and you may not need to call for service.Problem Possible Cau

21Problem Possible Causes What To DoWater hard sometimes Using hot water while the water • Avoid using hot water during water softening system softeni

Before you call for service…22Problem Possible Causes What To DoSalty tasting or Unit not sanitized • Complete the Sanitization Procedures on page 12.

23Parts list. ge.com

24Parts list.

25Parts catalog. ge.com GENERAL ELECTRIC PARTS CATALOGGNSF35ZREF. NO. PART NO. PART DESCRIPTION (04)0003 WS35X10001 O-RING SEAL KIT 10004 WS34X10005 D

26Parts catalog.GENERAL ELECTRIC PARTS CATALOGGNSF35ZREF. NO. PART NO. PART DESCRIPTION (04)0101 WS02X10012 SCREW, #4 – 24 X 1-1/8″ 10102 WS02X10013 S

27What Is Not Covered:For The Period Of: We Will Replace:One Year Any part of the Water Softening System which fails due to a defect in materials or w

28Consumer Support. GE Appliances Websitege.comHave a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, a

3Installation Water Softening SystemInstructionsModel GNSF35ZQuestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.comBEFORE BEGINN

Installation Instructions4UNPACKING AND INSPECTIONBe sure to check the entire softener for anyshipping damage or parts loss. Also note damageto the sh

5Installation InstructionsPLAN HOW YOU WILL INSTALL THESOFTENERYou must first decide how to run in and out pipes to the softener. Look at the house ma

INSTALL BYPASS VALVE• Remove plastic shipping plug and wire from valveoutlet.• Push the bypass valve (lubricate o-ring seals withsilicone grease) into

PLUMB “IN” AND “OUT” PIPES TO AND FROM SOFTENERCAUTION: Observe all of the followingcautions as you connect inlet and outletplumbing. See Typical Inst

Installation Instructions8CONNECT AND RUN THE VALVEDRAIN HOSE (CONT.)• Elevating the drain hose may cause back pressure that could reduce the brine dr

INSTALL GROUNDING CLAMPDANGER: Failure to properly attachground clamp could result in electrical shock.If plumbing is metal, to maintain electrical gr