GE PSFA Installationsanleitung PDF herunterladen (Seite 1)

GEH-3899C

INSTRUCTIONS

Optical/Lamp Holder

for Remote Ballast

READ THOROUGHLY BEFORE INSTALLING

GENERAL

This lamp holder is designed for indoor and outdoor lighting applications. It is for use with either a

General Purpose or Heavy Duty Powr•Spot

oodlight optical which is shipped in a separate carton. Check

to see that you have received the correct material.

UNPACKING

This lamp holder has been properly packed so that no parts should have been damaged during

transit. Inspect to conrm.

INSTALLATION

CAUTION

Unit will fall if not installed properly

• Follow installation instructions

WARNING

Risk of electric shock

• Turn power o before servicing

– see instructions

NOTE: Optical assembly is keyed for proper orientation.

1. Align keyhole slots in optical with mounting screws in lamp holder.

2. Rotate optical clockwise (approximately 5°).

3. Tighten mounting screws.

A trunnion bracket is provided for installation on at surfaces with a 3/4-inch bolt. Special mounting

adaptors are available for other applications. The degree scale permits setting the lamp holder to

predetermined vertical angle.

NOTE: Install unit so that the wiring compartment is located on underside of unit. (Figure 1)

Tighten Trunnion side bolts to 80 - 90 foot pounds.

FIGURE 1

CAUTION

Risk of burn

• Allow lamp/xture to cool before handling

FIGURE 2

Lighting Solutions

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered suciently for the purchaser’s purposes, the matter should be referred to

GE Lighting Solutions.

WIRING

Make all electrical connections in accordance with the National Electrical Code and any applicable

local code requirements.

NOTE: Cable strain relief and sealing are provided by the compression plate and rubber bushing

supplied for 9/16-inch O.D. cable. Three-conductor, AWG No. 14 cable is recommended.

1. Open wiring compartment cover.

2. Insert cable through compression plate and rubber bushing and secure by tightening screws.

3. Make electrical connections and replace wiring compartment cover.

AIMING

NOTE: TWO (2) REFLECTOR DIAMETERS ARE ACCOMMODATED. THE HIGH U-SHAPED CUTOUT OF

THE SIGHT BAR IS USED WITH 22’’ DIAMETER REFLECTORS. THE LOW POSITION IS USED WITH 20’’

DIAMETER REFLECTORS.

1. Insert aiming sight into spot on top of lamp holder.

2. Loosen trunnion clamping bolts and align U-shaped cutout in sight bar with center of top door glass

clip.

3. Tighten trunnion clamping bolts to 80 - 90 foot pounds and remove sight.

MAINTENANCE

Periodic cleaning on the outside of the door glass will ensure operation at maximum optical eciency.

The glass and reector (if needed) should be cleaned with non-abrasive soap, cleaner, or detergent

solutions; rinsed with cold water and wiped dry.

The light output is also dependent on the age of the lamp. In applications where the light level is

critical it may be desirable to replace lamps before they burn out. The lamp manufacturer can provide

data showing how the lamp light output decreases with use.

Relamping:

Use only lamps specied on nameplate. Observe lamp manufacturer’s recommendations and

restrictions on lamp operation, particularly ballast type, burning position, etc.

Lamp Tightness – Mogul Base Lamp: The lamp should be securely inserted to the NEMA-EEI specied

torque of 35 inch-pounds, which is best achieved by very rmly tightening to insure application of sucient

torque. Tightening must be sucient to fully depress and load the center contact of the socket.

1. Open glass door. (Unlatch top clip last.)

2. Relamp and close glass door. (Latch top clip rst, checking gasket for proper seating, then latch other

clips).

1 2

Inhaltsverzeichnis

Seite 1 - Optical/Lamp Holder

GEH-3899CINSTRUCTIONSOptical/Lamp Holderfor Remote BallastREAD THOROUGHLY BEFORE INSTALLINGGENERALThis lamp holder is designed for indoor and outdoor

Seite 2 - 1 6 9 4 3 5 3 3- - -- 8 8 8

35-201578-C9 ( Rev. 04/13/11)GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Evolve and the GE brand and logo are trade

Weitere Dokumente für Nein GE PSFA

Um das Dokument anzuzeigen GE PSFA Installationsanleitung

GE PSFA Installationsanleitung (4 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Aaeon FOX-12D User Manual (60 pages)

Brand: Aaeon | Category: Computers | Size: 1.62 MB |

FOX-12D

Acknowledgments

Packing List

Safety & Warranty

Contents

Chapter

LCD Display FOX-12D

Power Supply

DC 9-30V

Touchscreen

1.4 Dimension

9 Not Used 10 Not Used

Latch is in place

More products and manuals for Computers Aaeon

Models	Document Type
ACD-518D	User Manual AAEON ACD-518D User Manual, 47 pages
ACD-521D	User Manual AAEON ACD-521D User Manual, 47 pages
AFP-6152	User Manual AAEON AFP-6152 User Manual, 34 pages
AGD-310D	User Manual AAEON AGD-310D User Manual, 62 pages
AGD-315D	User Manual AAEON AGD-315D User Manual, 66 pages
AGD-317D	User Manual AAEON AGD-317D User Manual, 64 pages
ACP-1103	User Manual AAEON ACP-1103 User Manual, 115 pages
ACP-5187	User Manual AAEON ACP-5187 User Manual [en] , 110 pages
ACP-5217	User Manual AAEON ACP-5217 User Manual, 108 pages
ACP-5215	User Manual AAEON ACP-5215 User Manual, 61 pages
ACP-5152	User Manual AAEON ACP-5152 User Manual, 62 pages
ACP-5185	User Manual AAEON ACP-5185 User Manual, 106 pages
ACP-5182	User Manual AAEON ACP-5182 User Manual, 62 pages
ACP-5212	User Manual AAEON ACP-5212 User Manual, 62 pages
ACP-5210	User Manual AAEON ACP-5210 User Manual, 81 pages

GE PSFA Installationsanleitung Seite 1