GE OBE Installationsanleitung PDF herunterladen (Seite 3)

The Luminaire wattage is preset at the factory. Please contact the

factory for instructions and a retrofit kit if a different wattage is

required.

Black Color = Primary Phase

White Color = Neutral or Secondary

Phase

Green Color = Fixture - Earth Ground

Violet Color = (+) 0-10VDC Dimming

Gray Color = (-) 0VDC Dimming

All

Nuvation

Models

Dimming

Nuvation

The NuVation ballast is rated for use with a supply voltage

between 208V and 277V with +/- 10% line voltage tolerance, 50/

60 Hz, and will automatically sense voltage within the specified

range.

The wire colors for the input lines in the wiring box are:

DC Control Voltage 0V +5V +10V

Output Level 50% 75% 100%

CAUTION

Risk of Electrical Damage

• DO NOT MISMATCH wattage setting

and Metal Halide HID Lamp wattage.

• Verify that the circuit wiring and

circuit breakers are rated for the total

circuit load.

DIMMING FEATURE / INSTRUCTIONS

The NuVation

™

meets the lamp manufacturers requirements of

starting/operating the lamp at high wattage for at least 15

minutes before any dimming control can happen.

For continuous operation (24 hr/day) the NuVation will

automatically go into a full power mode once a day for at least 15

minutes as required by lamp specifications.

WIRING NOTES: Polarity of the dimming control leads

(VIOLET + and GRAY -) must be maintained.

DIMMING CONTROL

Dimming control is accomplished by connection to the

VIOLET + AND GRAY –

Wires in the wiring box (Figure 2). See Diagram A for wiring

schematic.

POLARITY MUST BE PROPERLY APPLIED

(VIOLET + To control +) AND (GRAY – To control -)

Shorting (example with a switch) the violet and gray wires will

cause the NuVation to operate at low wattage, removing the short

will cause the lamp to operate at full wattage.

External control systems can be used to operate the bi-level

function.

Diagram A

A zero (0) to ten (10) volt DC power supply can control the bi-level

operation.

This can be either to continuously adjustment lamp wattage 50%

to 100 %.

Or one step 50% to 100%.

POLARITY MUST BE PROPERLY APPLIED

(VIOLET + To control +) AND (GRAY – To control -)

A resistor or potentiometer (pot) can also be used to continuously

adjust lamp wattage by connecting to the VIOLET + and GRAY –

wires. The resistor or potentiometer should be in the 0 – 50K ohm

range. The voltage output from the VIOLET + and GRAY – wires will

be in the 0-10 volt range and current will be less than one (1)

milliamp.

Added Features of the GELS NUVATION ™

• Automatic lamp shut off if the lamp fails to start within 90

minutes

• After a power shut off the NUVATION must be switched off and

then back on (cycle time 1 to 2 seconds).

Automatic lamp shut off for end of life high voltage lamps

FINAL ASSEMBLY

OPTICAL ASSEMBLY/MOUNTING

UGE, VBE, UWE, UTE, OBE, UME, MBE

1. Secure the reflector to the bottom of the ballast housing as

shown in Figure 6. Installation is aided by keyhole slots in

reflector.

1a. On VBE and MBE units with Safety Chains, orient the reflector

so that the Ballast Housing and Reflector Safety Chain

Attachment Holes are on the same side.

1b. On VBE units push the Reflector Mounting Bracket thru the

reflector opening and slide it over the Socket Brackets all the

way. On 400 watt Metal Halide units the top (first) hole of the

Mounting Bracket will snap over the Socket Bracket screws.

On all others, the bottom (second) hole will snap over the

bracket screws. See Figure 7. For additional assembly

instructions, refer to the instruction sheet that came in the

small box with the metal reflector and -mounting bracket.

Keyhole

Slots

Reflector

Figure 6 Figure 7 Figure 8

Locking

Tabs

Locking

Tabs

Socket

Quartz

Socket

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

GE OBE Installationsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein GE OBE