GE DSR-1000eZ Bedienungsanleitung Seite 12
- Seite / 64
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Calibur DSR-1000eZ 1-6 0150-0238A
Alarm In
An alarm condition can be activated by an Active Low TTL input
or by relay contact devices such as pressure pads, passive
infrareds, door switches, or other similar devices.
Input: Active Low TTL w/ pull-ups
or Normally Open Relay.
High: 5V (12V tolerant)
Low: Ground
Minimum Duration: 0.5 Seconds
Figure 1-4 Normally Open Relay Alarm Connection
Pin 1
Pin 7 or 10
Alarm Input
Ground
Accessories PCB
Typical Alarm Device
Refer to each alarm devices's
manual for specific wiring details.
Normally Open
(Closes During Alarm)
Alarm Out
The Alarm output is activated when a teletext alarm is detected,
or while the Alarm Input is active. The Alarm output is only
active for the duration of the alarm event.
Output: Active Low
High: 12V
Low: Ground
Current Out: 50mA Max
Short Circuit Protected.
Low for duration of alarm.
Record Start In
Record Start In will place the unit in Record mode when
activated. Compatible with the Disk End Out signal from a
second unit.
Input: Active Low TTL w/ pull-ups
or Normally Open Relay.
High: 5V (12V tolerant)
Low: Ground
Minimum Duration: 0.5 Seconds
Alarm Record Reset
This feature is for future development, and has not yet been implemented.
- CONTENTS 5
- 1.1 Product Description 7
- 1.2 Features 7
- 1.3 Unpacking 7
- 1.4 Installation Environment 8
- 1.5 Passwords 8
- 1.6 Front Panel Controls 8
- 1.7 Back Panel Connections 9
- Power Connector 10
- SCSI Port 10
- RS-232 Serial Port 11
- Alarm In 12
- Alarm Out 12
- Record Start In 12
- Alarm Record Reset 12
- Videoloss Out 13
- Disk End Out 13
- VEXT Pulse Out 13
- Error Out 13
- 1.10 Setting the Alarms 15
- 2 USER OPERATIONS 17
- 2.2 Playback 18
- 2.3 The Search Interface 19
- Selecting Cameras to Search 20
- Starting the Search 21
- 3 THE MENU SYSTEM 23
- Entering the Main menu 24
- The Main Menu 24
- Main Menu → Timer Settings 25
- Main Menu → Record Settings 25
- Main Menu → Display Settings 25
- Main Menu → Archive Setup 25
- Ethernet information will not 26
- Do You want to continue? 27
- Erase Disk 27
- [CANCEL] [OK] 27
- ADM Setting 28
- 30 Days 28
- 4 OPERATOR PROGRAMMING 31
- 4.2 Main Menu → Alarms 32
- Creating a Timed Recording: 34
- Editing a Timed Recording: 34
- Deleting a Timed Recording: 35
- Specifying Search Parameters 39
- Starting the Archive Process 40
- 5 INSTALLER PROGRAMMING 45
- Unit records over 46
- Modem Settings 49
- Modem Status : DISABLE 49
- Firmware Upgrade 53
- [CANCEL][OK] 53
- 6 RS-232 REMOTE PROTOCOL 55
- Setting the Clock 56
- 7 FACTORY DEFAULTS 59
- 8 TECHNICAL SPECIFICATIONS 61
- On-screen Video Indicators 62
- Part Numbers 62
- 9 WARRANTY AND SERVICE 63
- Advance Replacement Policy 64
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme GE DSR-1000eZ
(36 Seiten)Cisco 6509-NEB - Catalyst Switch manuels
Manuels d'utilisation et guides de l'utilisateur pour Mise en réseau Cisco 6509-NEB - Catalyst Switch.
Nous fournissons des manuels en pdf 1 Cisco 6509-NEB - Catalyst Switch à télécharger gratuitement par type de document : Guide d'installation
Kommentare zu diesen Handbüchern