GE RAK7023 Installationshandbuch PDF herunterladen

Tools Needed

• Phillips head screwdriver • Center punch

• Drill and 1/4” bit • Hammer

• 1/4” and 5/16” Nut drivers • Gloves

3. For AZ21 or AZ31 series:

a. Remove the two thumb screws securing the

transition duct to the bottom of the lateral

duct adapter.

b. Carefully slide the transition duct forward

and remove.

c. Remove room cabinet front.

4. The old transition duct, the three screws

(if used) and any gaskets used to seal the

old transition duct to the chassis will not be

needed for the new installation but should be

kept for possible reuse of the old chassis in

this installation location.

5. Remove the chassis-to-case screw (two on

each end of the chassis) and carefully slide it

from the case.

Parts Included

• Transition duct assembly

• Metal seal strip

• Metal clips (2)

• Thumb screws (2)

Important Notes

• This instruction describes how to modify an

existing GE duct adapter to be used with the

new AZ45 and AZ65 Series.

Transition duct

STEP 1

Removal of the chassis from the

case

1. Disconnect the power to the unit.

2. For AZC or AZR series:

a. Remove room cabinet front.

b. Remove the three screws securing the

transition duct to the bottom of the lateral

duct adapter.

c. Carefully slide the transition duct forward

and remove (see illustration in next step).

Lateral duct adapter

”

Installation Instructions

for your new

Before you begin - Read these instructions completely and carefully.

IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

RAK7023

Transitional duct adapter

Pub No. 31-30808-1 07-16 GEA

GE is a trademark of the General Electric Company. Manufactured under trademark license.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Tools Needed• Phillips head screwdriver • Center punch• Drill and 1/4” bit • Hammer• 1/4” and 5/16” Nut drivers • Gloves3. For AZ21 or AZ31 serie

Seite 2 - Chassis modification and

STEP 2 Thumb screw hole location (This step is necessary only if thumb screws were not previously used.)1. Slide the new transition duct into place.

Seite 3 - Transition duct

STEP 3 (continued)5. Reconnect power and check operation. Insure the unit is in duct mode. To do this, turn unit off. Press the red “AUX” button and p

Seite 4

Seite 5 - Instructions d’installation

Outils requis• Tournevis à tête cruciforme • Pointeau• Perceuse et foret de 1/4 po • Marteau• Tournevis à douille de • Gants 1/4 po et 5/6 po 3.

Seite 6 - (Cette étape est requise

ÉTAPE 2 Emplacement de trou de vis de serrage à main (Cette étape est requise uniquement si les vis de serrage à main n’ont pas été utilisées précéde

Seite 7 - Filtres à air

ÉTAPE 3 (suite)5. Rebranchez l’alimentation et vérifiez le fonctionnement. Assurez-vous que l’unité est en mode conduit. Pour ce faire, éteignez l’app

Seite 8

Kommentare zu diesen Handbüchern

Keine Kommentare

GE RAK7023 Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Nein GE RAK7023 herunter. GE RAK7023 Installation Instructions [de] [en] [fr] [it] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein GE RAK7023