GE H4 Installationsanleitung PDF herunterladen

GEH-5734B

INSTRUCTIONS

H4 Hazardous Location Luminaire

READ THOROUGHLY BEFORE INSTALLING

WARNING: DANGEROUS VOLTAGES EXIST

WITHIN THESE UNITS AND ALL PRECAUTIONS

USUALLY OBSERVED IN HANDLING HIGH

VOLTAGE EQUIPMENT SHOULD BE OBSERVED.

MAKE CERTAIN POWER IS OFF BEFORE

STARTING INSTALLATION PROCEDURE OR

BEFORE SERVICING.

Caution: When installing the luminaire in hazardous

locations, check the operating temperature limits prior to

installation to be sure it conforms to the environmental

temperature restrictions and NEC classifications.

THIS FIXTURE SHOULD BE INSTALLED BY QUALIFIED

TECHNICIANS IN STRICT ACCORDANCE WITH THE NA-

TIONAL ELECTRICAL CODE AND ANY LOCAL REQUIRE-

MENTS.

INSTALLATION

Caution: To avoid electrical shock hazard.

1. Before installation or service of this fixture,

make sure that the circuit is deactivated.

2. This unit is furnished completely assembled.

Before installing, check the fixture label to

insure correct voltage and frequency.

3. Typical fixture installations are shown on

back of page.

OPERATIONAL DATA

Operate this fixture at its rated voltage. See fixture label for

data. To receive full benefit of rated lamp output and to

prolong ballast life, it is essential that voltage supply to the

fixture be maintained within the following limits:

NOMINAL APPLIED VOLTAGE RANGE

VOLTAGE MINIMUM MAXIMUM

120 110 125

277 255 290

MAINTENANCE DATA

1. Although no routine maintenance is required to keep this

fixture functional, it should be checked perodically to ensure

that it is working properly and to look for any external

damage.

2. For optimum performance, keep light transimissions parts of

the fixture clean. Any commercial glass cleaner can be used

to clean the glass tubes.

3. Relamping Procedure:

A. Biaxial Lamp — Disconnect supply circuit. Remove the

lamp access cover (opposite conduit entrance side).

Using the relamp support, remove the lamp from the

fixture. Remove the lamp support and install on new

lamp. Install lamp and lamp access cover.

B. T8/T5 Lamp — Disconnect supply circuit. Remove

lamp access cover (either end of lamp). Loosen

lampholder bracket screws. Twist and remove

lampholder bracket. Remove lamp and install new lamp,

seating lamp in opposite lampholder. Replace

lampholder into position on the lamp. Twist slightly to

place lampholder bracket under screw heads, and tighten

screws. Reattach lamp access cover.

4. In the event of glass tube breakage, it will be necessary to

replace the damaged unit with a factory sealed housing

assembly, in order to maintain the integrity of the fixture.

See the fixture parts list for ordering.

5. When replacing Ballast, it should be of Class-P, thermally-

protected type.

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred

to GE Lighting Solutions.

Lighting Solutions

1 2

INSTRUCTIONS 1
TYPICAL INSTALLATIONS 2

Inhaltsverzeichnis

Seite 1 - INSTRUCTIONS

GEH-5734BINSTRUCTIONSH4 Hazardous Location LuminaireREAD THOROUGHLY BEFORE INSTALLINGWARNING: DANGEROUS VOLTAGES EXISTWITHIN THESE UNITS AND ALL PRECA

Seite 2 - TYPICAL INSTALLATIONS

TYPICAL INSTALLATIONS(Mounting Hardware/Supports by others)Dummy (non-powered) end lowers for relamping clearancewhich is required when fixtures are m

Kommentare zu diesen Handbüchern

Keine Kommentare

GE H4 Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach Nein GE H4 herunter. GE H4 Installation Guide Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein GE H4